Part 1: Set Up Topology and Configure Basic Router and Switch Settings Step 1: Cable the network as shown in the topology. Step 2: Initialize and reload the router and switch. Step 3: Verify that the PC interfaces are configured to use the IPv6 protocol.
This should allow communication between the clients on the old and new network on the same vlan to communicate with each other. E.g. for VLAN 10, the existing network is 192.168.100.0/24 with the gateway (non-Cisco router) being 192.168.100.1 and the new network is 10.10.100.0/24 with new gateway 10.10.100.1. MAIN Router LAN IP is 192.168.2.1 - do not change SECOND Router Original LAN IP is 192.168.0.1 - needs to be changed to 192.168.2.2 or 192.168.2.3 etc. After changing SECOND Router's LAN IP address do not forget to APPLY or SAVE these changes. 13. Next step is to get new IP address on the computer. You can just restart computer or disconnect Hi, I wish to configure 2 linksys wrt54g/s routers on one network. I have the first as my gateway to the internet and there are 2 PC's connected to it. I have linked the second router to the first That’s where this tip comes in. By configuring two IP addresses on a computer, I can connect to it, that is, if I am on the same subnet or VLAN. That way I have the best of both worlds — my regular IP address to access the internet or email and an IP address in the same subnet as the factory IP address.
There are times when having two separate networks - both sharing the same Internet connection - can come in handy. For example, I recently helped a community center with its network setup. They needed to provide Internet connection to tenants who were renting space, in addition to their own shared Internet.
Nov 12, 2003 · Setting Up. Figure 1 shows the basic network configuration, which is based on the setup I used for my community center project. It uses three routers - one to share the Internet, and two more to Looking at the above diagram you can see that subnets 192.168.10.0/27 and 192.168.10.32/27 which belong to the same classful network 192.168.10.0/24 are separated by network 10.0.0.0 hence they are considered to be discontiguous networks. Jul 25, 2011 · 2. The closet is not in the center of the house and therefore the signal barely reaches the opposite side of the house and doesn’t work very well upstairs either. Eventually, I decided that I would have to get another wireless router and somehow set it up as a second wireless router to complement the main wireless network.
Use the same SSID and password but put it on a different channel. If router 1 has it's wireless on channel 1, use channel 11 on router 2. Once configured, wireless clients can connect to the WLAN on router 2 and will get their DHCP settings from the DHCP server on router 1. Which is to say, disable DHCP on router 2.
The problem is with this one, we need to connect a computer on G0/2. This computer is configure as network A (192.198.0.10 / 255.255.255.0 and same gateway). I can't configure G0/2 as 192.198.0.1 255.255.255.0 (network A), cause G0/0 use this adresse. I can't put this computer on the switch A, my only physical possibilité is to connect him on Apr 18, 2017 · In this video i will show How to connect two routers in one network Like Share & Subscribe Thanks for Watching. Feb 06, 2017 · Router# show running-config router rip version 2 network 10.0.0.0 network 192.168.1.0 no auto-summary! Verifying RIP Configuration To verify that you have properly configured RIP, enter the show ip route command and look for RIP routes signified by “R” as shown in this example. After I have everything set up as you did, I plan to configure yet another (third) router at my neighbor's in bridge mode to let him connect his WD TV Live to my NAS. I am puzzled by the warnings in the router manual that router acting as a bridge _must_ have the same channel as the wireless network it is bridging to. Save your changes, reboot the router and log back into the router at its new address, for example, 192.168.1.2, and enter the new administrative password you assigned. Disable the DHCP server. Disable the firewall and set the router type to Router instead of Gateway if that’s an option. HOw to setup two routers from two different ISPs to share same network By clarencefm · 7 years ago One of my clients recently subscribed to a second ISP and is connected using a UMAX router (WIMAX).